- 相關推薦
船舶與海洋工程英語閱讀：船舶設計師
The Naval Architect 船舶設計師
A naval architect asked to design a ship may receive his instructions in a form ranging from such simple requirements as “an oil tanker to carry 100 000 tons deadweight at 15 knots” to a fully detailed specification of precisely planned requirements. He is usually required to prepare a design for a vessel that must carry a certain weight of cargo (or number of passengers ) at a specified speed with particular reference to trade requirement; high-density cargoes, such as machinery, require little hold capacity, while the reverse is true for low-density cargoes, such as grain.
Deadweight is defined as weight of cargo plus fuel and consumable stores, and lightweight as the weight of the hull, including machinery and equipment. The designer must choose dimensions such that the displacement of the vessel is equal to the sum of the dead weight and the lightweight tonnages. The fineness of the hull must be appropriate to the speed. The draft------which is governed by freeboard rules------enables the depth to be determined to a first approximation.
After selecting tentative values of length, breadth, depth, draft, and displacement, the designer must achieve a weight balance. He must also select a moment balance because centres of gravity in both longitudinal and vertical directions must provide satisfactory trim and stability. Additionally, he must estimate the shaft horsepower required for the specified speed; this determines the weight of machinery. The strength of the hull must be adequate for the service intended, detailed scantlings (frame dimensions and plate thicknesses ) can be obtained from the rules of the classification society. These scantings determine the requisite weight of hull steel.
The vessel should possess satisfactory steering characteristics, freedom from troublesome vibration, and should comply with the many varied requirements of international regulations. Possessing an attractive appearance, the ship should have the minimum net register tonnage, the factor on which harbour and other dues are based. (The gross tonnage represents the volume of all closed-in spaces above the inner bottom. The net tonnage is the gross tonnage minus certain deductible spaces that do not produce revenue. Net tonnage can therefore be regarded as a measure of the earning capacity of the ship, hence its use as a basis for harbour and docking charges. ) Passenger vessels must satisfy a standard of bulkhead subdivision that will ensure adequate stability under specified conditions if the hull is pierced accidentally or through collision.
Compromise plays a considerable part in producing a satisfactory design. A naval architect must be a master of approximations. If the required design closely resembles that of a ship already built for which full information is available, the designer can calculate the effects of differences between this ship and the projected ship. If, however, this information is not available, he must first produce coefficients based upon experience and, after refining them, check the results by calculation.
Training
There are four major requirements for a good naval architect. The first is a clear understanding of the fundamental principles of applied science, particularly those aspects of science that have direct application to ships------mathematics, physics, mechanics, fluid mechanics, materials, structural strength, stability, resistance, and propulsion. The second is a detailed knowledge of past and present practice in shipbuilding. The third is personal experience of accepted methods in the design, construction, and operation of ships; and the fourth, and perhaps most important, is an aptitude for tackling new technical problems and of devising practical solutions.
The professional training of naval architects differs widely in the various maritime countries. Unimany universities and polytechnic schools; such academic training must be supplemented by practical experience in a shipyard.
Trends in design
The introduction of calculating machines and computers has facilitated the complex calculations required in naval architecture and has also introduced new concepts in design. There are many combinations of length, breadth, and draft that will give a required displacement. Electronic computers make it possible to prepare series of designs for a vessel to operate in a particular service and to assess the economic returns to the shipowner for each separate design. Such a procedure is best carried out as a joint exercise by owner and builder. As ships increase in size and cost, such combined technical and economic studies can be expected to become more common.
(From “Encyclopedia Britannica”, Vol. 16, 1980)
【船舶與海洋工程英語閱讀：船舶設計師】相關文章：
船舶與海洋工程個人簡歷06-13
船舶與海洋工程專業大學生簡歷范文09-22
上海交通大學船舶與海洋工程專業就業前景09-05
有關船舶海運的外貿英語術語08-28
船舶英文簡歷范文10-14
船舶個人簡歷封面09-05
國際航行船舶通關概述08-25
船舶個人簡歷封面(2)07-04
國際航行船舶的通關概述07-17